Amps: 3; Depth: 5.71"; Height: 5.50"; HP: 0.75; Mfg. #: HSKA1200055-E1; Volts: 200/240; Width: 2.95"; Wt. Lbs.: 7;
| Store | Status |
| Login above to see availability | |
Amps: 3; Depth: 5.71"; Height: 5.50"; HP: 0.75; Mfg. #: HSKA1200055-E1; Volts: 200/240; Width: 2.95"; Wt. Lbs.: 7;
Efficiently control motor performance over a wide speed range in applications such as fans, blowers, condensers and conveyors |Control both voltage and frequency that the motor sees to properly control the motor speed |Reduce energy consumption and improve motor control |Configurations for HVAC, fan, pump control, torque control and PID (Proportional Integral and Derivative) set point controls
Starts up out of the box on V/Hz mode, and can operate in open loop vector mode |Simple pushbutton set up — no need for complex programming |Compact design — built-in filter, logicstick to unlock PLC capability |Communications port RS485-Modbus RTU as standard |Software and documentation CS included |G80-560 is single-phase, all others three-phase, 60Hz |Drives should be sized so that max amps is equal to or greater than motor name plate FLA |LONworks, Ethernet and other protocols available as options |All ratings are for normal duty with an overload capacity of 110% for one minute (normal duty rating is typically used in applications with variable torque loads, such as fans and centrifugal pumps) |A complete offering of variable frequency drives is available to Johnstone up through a 200 HP rating
| HP | 0.75 |
| Wt. Lbs. | 7 |
| Depth | 5.71" |
| Height | 5.50" |
| Volts | 200/240 |
| Amps | 3 |
| Features | Starts up out of the box on V/Hz mode, and can operate in open loop vector mode |Simple pushbutton set up — no need for complex programming |Compact design — built-in filter, logicstick to unlock PLC capability |Communications port RS485-Modbus RTU as standard |Software and documentation CS included |G80-560 is single-phase, all others three-phase, 60Hz |Drives should be sized so that max amps is equal to or greater than motor name plate FLA |LONworks, Ethernet and other protocols available as options |All ratings are for normal duty with an overload capacity of 110% for one minute (normal duty rating is typically used in applications with variable torque loads, such as fans and centrifugal pumps) |A complete offering of variable frequency drives is available to Johnstone up through a 200 HP rating |
| Width | 2.95" |
| Applications | Efficiently control motor performance over a wide speed range in applications such as fans, blowers, condensers and conveyors |Control both voltage and frequency that the motor sees to properly control the motor speed |Reduce energy consumption and improve motor control |Configurations for HVAC, fan, pump control, torque control and PID (Proportional Integral and Derivative) set point controls |
| Shipping Weight | 6.85 |
| Shipping Width | 14.30 |
| Shipping Length | 14.40 |
| Shipping Height | 10.60 |
| Harmonize Code | 8504.40.4000 |
| Note | Figure E is representative of drives listed. Actual dimensions are reflected in the table and may slightly alter the proportions of the drives. |
See catalog page 185 for additional notes and/or restrictions.
WARRANTY - Johnstone Supply will administer and promptly process all warranties in accordance with the manufacturer's specific warranty policies and procedures.
WHOLESALE ONLY - Identification is required of purchasers. Possession of Johnstone's catalog does not constitute an offer to sell by Johnstone or the right to purchase from us.
RETURNS - All returns are subject to a restocking charge.
Mfg. #: HSKA1200055-E1
Your Request is Processing ...
Your session is about to expire, would you like to continue?
Copyright © 2013 Johnstone Supply. All rights reserved.
This site is optimized for IE7 or later, Firefox, Chrome and Safari
